ANSI ATIS1000610-1998 电信.控制综合服务数字网(ISDN)补充业务的通用程序
作者:标准资料网 时间:2024-05-20 02:12:46 浏览:9771
来源:标准资料网
【英文标准名称】:Telecommunications-GenericProceduresfortheControlofISDNSupplementaryServices
【原文标准名称】:电信.控制综合服务数字网(ISDN)补充业务的通用程序
【标准号】:ANSIATIS1000610-1998
【标准状态】:现行
【国别】:美国
【发布日期】:1998
【实施或试行日期】:
【发布单位】:美国国家标准学会(US-ANSI)
【起草单位】:ANSI
【标准类型】:()
【标准水平】:()
【中文主题词】:入口控制;检查;通信网;数字连接;综合服务数字网络;综合业务数字网;网络互连;网络接口;补充业务;电信
【英文主题词】:Accesscontrols;Checks;Communicationnetworks;Digitalconnections;Integratedservicesdigitalnetwork;ISDN;Networkinterconnection;Networkinterfaces;Supplementaryservices;Telecommunications
【摘要】:
【中国标准分类号】:M21
【国际标准分类号】:33_080
【页数】:
【正文语种】:英语
【英文标准名称】:Inlandnavigationvessels;outboardladders
【原文标准名称】:内河航运船只.外甲板梯子
【标准号】:DIN83512-1985
【标准状态】:现行
【国别】:德国
【发布日期】:1985-12
【实施或试行日期】:1985-12-01
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:水路运输工程部件;跳板(船用);作标记;梯子;爬高装置;检验;尺寸;材料;安全工程;规范(审批);设计;荷载;造船;内河运输;安全
【英文主题词】:materials;shipbuilding;safety;safetyengineering;dimensions;watertransportengineeringcomponents;loading;inlandwaterwaytransport;climbingdevices;marking;design;specification(approval);ladders;ga
【摘要】:
【中国标准分类号】:U26
【国际标准分类号】:5065
【页数】:5P;A4
【正文语种】:德语
Product Code:SAE J356
Title:Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*
Issuing Committee:Metallic Tubing Committee
Scope:The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead.This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.) The primary differences between SAE J356 and SAE J356 Type-A are described in the following paragraph.Type-A tubing is heat treated in-line to relieve stresses and is generally produced in coiled form. When Type-A tubing is produced in coil form, straight lengths of Type-A are only available through a secondary straightening and cut-to-length operation. Standard SAE J356 is produced as straight lengths and then receives a secondary normalizing operation. All standard SAE J356 requirements apply to Type-A tubing unless the specific requirement is noted with a 脪Type-A脫 designation. Standard SAE J356 is also available in the same sizes as Type-A, in which case all the standard SAE J356 specifications apply.
